Network & IP

IPv4 + IPv6 Dual Stack: Use IPv6 to Get the Right Region for YouTube Premium and Gemini

9 étapes 13 min de lecture 71 vues 0
Sommaire

When a server has both IPv4 and IPv6, the operating system reaches IPv6-capable sites over IPv6 and everything else over IPv4. If a service such as Google places your IPv4 address in the wrong region, the IPv6 address is often located correctly, so YouTube Premium, Gemini and similar services work normally again. This guide explains why it happens, shows a real test on a Korea server, and walks through enabling and verifying IPv6.

Before You Start

  • A Linux server (Debian, Ubuntu, Rocky Linux or AlmaLinux) with curl installed.
  • IPv6 available in the server's data center. In IMIDC's Korea data center you can get IPv6 free of charge from the control panel.
  • SSH access. Before you change network settings, open the VNC console in the control panel so you still have a way in if something goes wrong.

Why Your IPv4 Address Gets the Wrong Region

Google and similar services do not rely only on IP registration records. They also use their own location data, built from how a range of addresses is actually used. If an IPv4 range is used heavily from other regions, the whole range can be assigned to a different place. This has nothing to do with where your server is or how it is routed: the server stays in the same data center, and its speed and stability do not change.

IPv6 has far more addresses and is handed out in smaller, more specific ranges, so its location data is usually more accurate. The same server reaching a service over IPv6 is usually recognized in its real country.

Test Results: Korea Server, IPv4 vs IPv6

Tested on 16 November 2026 from a server in IMIDC's Korea data center, once over IPv4 and once over IPv6:

ServiceIPv4IPv6
YouTube PremiumRegion detected incorrectlyDetected as Korea (GL=KR)
Google GeminiRegion detected incorrectlyDetected as Korea (KOR)
NetflixAvailable, full US catalogAvailable, full Korea catalog
ChatGPT, Claude, CopilotAvailableAvailable
Prime Video, TikTokKorea regionNo IPv6 support yet, IPv4 is used automatically

Services that support IPv6 are identified correctly over IPv6, and services without IPv6 simply stay on IPv4, so the two complement each other. Full results are in the Korea node AI and streaming unlock report.

Step 1: Get a Free IPv6 Address

Request IPv6 for your server in the control panel (free in the Korea data center). After it is assigned, reboot the server so the new network configuration takes effect.

Step 2: Check That IPv6 Works

Run this on the server:

curl -6 -s https://www.cloudflare.com/cdn-cgi/trace | grep -E '^(ip|loc)='

You should see ip= followed by your server's IPv6 address, and loc= followed by the server's country (for example KR). If nothing is printed or you get an error, IPv6 is not working yet; see the FAQ below.

Step 3: Confirm Google Uses IPv6

curl -6 -s https://www.youtube.com/premium | grep -o '"INNERTUBE_CONTEXT_GL":"[A-Z]*"'

If the output is "INNERTUBE_CONTEXT_GL":"KR" (your server's country code), Google reaches your server over IPv6 and sees the correct region.

Linux prefers IPv6 by default, so nothing else needs to be set. If you previously edited /etc/gai.conf and added the line precedence ::ffff:0:0/96 100 (which makes IPv4 preferred), comment it out to restore IPv6 preference.

Why IPv4 + IPv6 Together Works Well

  • More accurate region detection: services that support IPv6 use it and see your real location.
  • No side effects: services without IPv6 keep using IPv4 automatically, with nothing to configure per service.
  • A fallback: if one protocol's region is misjudged, the other still works.
  • No extra cost: IPv6 is free in the control panel.

FAQ

What if IPv6 does not work?

Run ip -6 addr show scope global. If you see two public IPv6 addresses and one is marked dynamic, the system has created an extra address from router advertisements and may use it for outgoing connections. Turn off autoconfiguration on the interface: with netplan, add accept-ra: false under the interface and run netplan apply; on Debian, add accept_ra 0 to the iface eth0 inet6 static section of /etc/network/interfaces and reboot. If it still does not work, open a ticket.

How can I make IPv4 region errors less likely?

Google judges a region from how a range of addresses is used. Not letting many devices from other regions share the same IP for long periods helps, but nothing can guarantee it. Enabling IPv6 is the simplest fix.

Will my account region change?

No. The country of your Google account, subscriptions and payment profile is set by the account itself. IPv6 only changes which region your network connection is detected in.

Will every service use IPv6?

Only services that support IPv6 (for example Google, YouTube and Netflix) use it. Services without IPv6 support yet, such as Prime Video and TikTok, keep using IPv4 automatically.

Summary

When an IPv4 address is placed in the wrong region, the cause is usually how that IP range has been used, not your server. Turning on free IPv6 while keeping IPv4 lets IPv6-capable services see your real region and leaves everything else as it was. It is the cheapest and simplest fix. For servers in Korea, see IMIDC Korea cloud servers and Korea dedicated servers.

Related Articles

Servers mentioned in this guide

Cette réponse était-elle pertinente ?

Tutoriels associés